Appliance Energy Cost Calculator
Pick an appliance or type in its power, say how long it runs, and see exactly what it adds to your bill — per day, week, month and year.
The results below are from your previous entries — fix the errors to update them.
Cost per year
—
| Period | Energy | Cost |
|---|---|---|
| Per day | — | — |
| Per week | — | — |
| Per month | — | — |
| Per year | — | — |
Power used: —. Estimate — real draw varies with settings and load.
How the calculation works
kWh per day = watts × hours per day ÷ 1,000
kWh per week = kWh per day × days per week
kWh per month = kWh per week × 52 ÷ 12 · kWh per year = kWh per week × 52
cost = kWh × rate per kWh
Example: a 1,000 W appliance used 2 hours a day, every day, at $0.1819/kWh uses 2 kWh a day and costs $0.36 a day — $132.42 a year.
Assumptions and limitations
- The appliance is assumed to draw the entered wattage for the whole time it is on. Cycling appliances (fridges, ovens, air conditioners) draw less on average; the preset list uses average draws for those.
- Amps × volts gives watts for resistive loads. For motor loads the true draw can differ slightly (power factor); the label wattage is preferable when printed.
- Preset wattages are typical midpoints, not measurements of your model.
Walking through the calculation, step by step
The calculator on this page does one thing, and it does it in the open: it turns the numbers you type into the answer shown in the result table, using the formula above it. There is no hidden adjustment and no extra factor added after the formula. If you can follow the formula line by line, you can check the calculator by hand, and that is exactly what this section does. Start with the first field, power, and read its help text before you type anything: the help tells you where the number comes from, and a number taken from the right place is the single biggest improvement you can make to the answer.
Here is the formula again, broken into its steps, in the order the calculator applies them:
- if power is in amps: watts = amps × volts Work through this line before moving on: every number in it comes from a field above, so a wrong entry here follows you into the answer.
- kWh per day = watts × hours per day ÷ 1,000 This line only changes the time scale of the answer: the same cost, expressed for a day, a month or a year.
- kWh per week = kWh per day × days per week This line only changes the time scale of the answer: the same cost, expressed for a day, a month or a year.
- kWh per month = kWh per week × 52 ÷ 12 · kWh per year = kWh per week × 52 This line only changes the time scale of the answer: the same cost, expressed for a day, a month or a year.
- cost = kWh × rate per kWh This is where the price enters the calculation: the amount of energy, multiplied by the price of one unit of it.
Watch the units as you go, because most mistakes in this kind of calculation are unit mistakes, not arithmetic mistakes. The fields on this page use these units: amps, days, hours, volts, watts. Power and energy are the pair that causes the most confusion: power, in watts or kilowatts, is a rate at which energy is used, and energy, in kilowatt-hours, is power multiplied by time. A 2,000 W heater running for one hour uses 2 kWh, and a 2 kW heater running for half an hour uses 1 kWh. Watts become kilowatts when you divide by 1,000, and kilowatt-hours are what your bill counts, so keeping those two apart is what makes the answer come out in the right size.
This page has no worked example with numbers, so make your own check instead. Run the calculator once with the starting values, write down the result, then change a single input by a round amount and run it again. The result should move in the direction the formula predicts: up when a quantity or a rate goes up, down when an efficiency goes up. If it moves the other way, you have found a wrong entry, not a wrong calculator, and the field help text is the first place to look.
How to read your result
The result table on this page answers the question in the title, and the first row in it is the headline: the total for the period you entered. The rows underneath it are not decoration. They show how the total is built, so that you can see which part of it is energy, which part is fixed charges, and what the cost works out to per day or per unit. If the total surprises you, the breakdown is where the surprise is explained: a total that looks high because of a fixed charge is a different problem from a total that looks high because of the amount used.
Read the result table row by row, in this order:
- Per day is the row to read when you want that part of the answer on its own. Compare it with the headline row: if it is most of the total, it is the part to work on first, and if it is small, changing it will not move the answer much.
- Per day is the row to read when you want that part of the answer on its own. Compare it with the headline row: if it is most of the total, it is the part to work on first, and if it is small, changing it will not move the answer much.
- Per week is the row to read when you want that part of the answer on its own. Compare it with the headline row: if it is most of the total, it is the part to work on first, and if it is small, changing it will not move the answer much.
- Per week is the row to read when you want that part of the answer on its own. Compare it with the headline row: if it is most of the total, it is the part to work on first, and if it is small, changing it will not move the answer much.
- Per month is the row to read when you want that part of the answer on its own. Compare it with the headline row: if it is most of the total, it is the part to work on first, and if it is small, changing it will not move the answer much.
To judge whether your own answer is high or low, change only the rate and watch the result. The rates register on this site lists a United States national reference rate of 0.1819 per kWh, a Washington average of 0.1442, a Massachusetts average of 0.3019 and a Hawaii average of 0.4641. At those rates, 1,000 kWh costs $181.90, $144.20, $301.90 and $464.10. The same 1,000 kWh at the North Dakota average of 0.1246 costs $124.60, and the Montreal record in the register is 0.0829 per kWh, which gives 0.0829 times 1,000, or 82.90, for 1,000 kWh. The spread between those records is wider than most people expect, and it is why the rate matters as much as the amount you use: the same usage can cost roughly four times as much at the highest of those rates as at the lowest, and no change in how you use electricity can close a gap that comes from the price itself.
What affects the result most
Not every input matters equally, and the ranking is written into the formula. An input that the formula multiplies by moves the answer in proportion: double it, and the answer doubles, as long as everything else stays the same. An input that the formula divides by moves the answer the other way: raise it, and the answer falls. A fixed charge is different again: it does not move at all when you use more, so it matters most when use is low and least when use is high. Before you spend effort improving an input, check where it sits in this ranking, because a precise number for a small input is worth less than a rough number for the biggest one.
- Power: raising this raises the result in proportion, because the formula multiplies by it. It is usually the input where a better measurement pays off first.
- Current: raising this raises the result in proportion, because the formula multiplies by it. It is usually the input where a better measurement pays off first.
- Voltage: raising this raises the result in proportion, because the formula multiplies by it. It is usually the input where a better measurement pays off first.
- Hours used per day: raising this raises the result in proportion, because the formula multiplies by it. It is usually the input where a better measurement pays off first.
- Days used per week: raising this raises the result in proportion, because the formula multiplies by it. It is usually the input where a better measurement pays off first.
- Standing charge: this adds the same amount every day, so it does not change when you use more energy. When use is low it can be a large share of the total, and when use is high it fades into the background.
A useful check is the doubling test. Take the starting values on this page, double the main quantity in your head, and ask what the formula would give: for a quantity the formula multiplies by, the answer doubles too. That is why the first thing to get right is the quantity itself — the amount used, the hours run, the area, or the distance — and the second thing is the rate or price. Everything else on the page is either a conversion between units, which the formula handles for you, or a fixed amount, which you can read straight from a bill.
Common mistakes
Most wrong answers from this calculator come from the same few slips. They are easy to make and easy to check for, and checking for them takes less time than re-doing the whole calculation:
- Mixing up watts and kilowatt-hours. Watts describe how fast an appliance uses energy; kilowatt-hours describe how much energy it has used. Entering a wattage where the calculator asks for energy, or the reverse, makes the answer wrong by a factor of a thousand or by the number of hours, and the mistake is easy to miss because the result still looks like a plausible number.
- Using the wrong rate. A preset average is a starting point, not your tariff. If your bill shows a different rate, use that one: the calculator multiplies by the rate you enter, so a rate that is a few cents out moves the whole answer by the same proportion.
- Mixing up the period. A monthly figure entered where the calculator asks for a year, or a daily figure where it asks for a month, throws the answer out by a factor of twelve or thirty. Check the unit next to every field before you type, and check the period the result is stated for before you compare it with a bill.
- Rounding too early. Rounding each step of a calculation before the next step uses the rounded number, and the rounding adds up. Enter the full numbers the calculator asks for, let it do the arithmetic, and round only the final answer when you quote it.
- Ignoring what the calculator leaves out. The assumptions section above lists what is not included in the answer — fixed charges, taxes, maintenance, installation and other costs, depending on the calculator. Treating the result as a complete bill, or as a complete saving, is the most common way to be disappointed by it afterwards.
Ways to lower the cost
The result on this page is a starting point, not a verdict. These are the practical ways to use it:
- Measure before you spend. Run the calculator with your real numbers first, and find which input drives the result, because the section above ranks them. Money spent on a small input buys a small reduction; the same money spent on the biggest input buys a bigger one.
- Check the rate before you change anything else. The rate scales the whole answer, and it is the one input you can sometimes change without changing how you live: a different tariff, a different time of use, or a corrected reading can move the result without any new equipment.
- Cut the quantity, not the comfort, where you can. Hours of use and duty cycle are quantities you control directly, and a small reduction in the hours something runs, or in how hard it works, reduces the cost in proportion. The calculator lets you test the reduction before you commit to it.
- Fix the fixed part separately. If the result table shows a large fixed or standing charge, reducing use will not reduce that part. That is a different problem from reducing use, and it is solved by looking at the tariff itself rather than at how much you use.
Frequently asked questions
Why does the calculator ask for power?
Because the formula needs it, and because it is the number most people get wrong. The help text next to the field says where the number comes from, and using the number from that source — a bill, a meter reading, a label, or a measured figure — is what makes the answer about your home rather than about an average one.
Can I use the preset rate, or should I use my own?
Use your own rate whenever you have it. The presets on this page are published averages or regulated figures, provided as starting points so the calculator works before you have a bill to hand. Your own rate, taken from a recent bill, is always the more accurate input, and the result moves in proportion to it.
Does the result include tax?
The calculator applies the rate you enter exactly as you enter it. If the rate you type already includes tax, the result includes it; if it does not, the result does not, and tax must be added afterwards. Where a calculator on this site has its own tax field, that field is the place to enter it, and the assumptions section above says which case applies to this page.
Why is my bill higher than this calculator's answer?
A bill can be higher than this calculator's answer for reasons the calculator does not include: fixed charges and taxes, other appliances and loads, an estimated reading, or a period that does not match the one you entered. Compare the result table row by row with the bill, and the row where the two diverge is the one to investigate.
Related calculators
- Electricity Bill Estimator — add up every appliance in the home at once.
- kWh Calculator — energy only, no prices.
- Air Conditioner Cost Calculator — sized by BTU and efficiency.