LED Savings Calculator
Lighting is one of the few upgrades with a payback measured in weeks: an LED uses roughly a seventh of the electricity of the incandescent bulb it replaces. Enter your bulbs, hours and rate to see the saving — including what the new bulbs cost.
The results below are from your previous entries — fix the errors to update them.
Money saved per year
—
| Electricity saved per year | — |
|---|---|
| Cost of the new bulbs | — |
| Payback time | — |
| Net saving over the projection (after bulb cost) | — |
Estimate — savings scale with the hours the lights are actually on.
How the calculation works
payback = bulb purchase cost ÷ money saved per year
Worked example
Ten 60 W bulbs replaced by 8 W LEDs, on 5 hours a day at 0.1819 per kWh: each bulb saves 52 W, so the set saves 949 kWh and $172.62 a year. At 3 per bulb (30 total), the swap pays for itself in about 2.1 months and nets $1,696.23 over ten years.
Assumptions and limitations
- Savings are counted only for the hours you enter, and old bulbs are assumed removed, not kept in the same sockets.
- Replacement bulbs for the old technology over the projection period are excluded (counting them would favour LEDs further — incandescents typically last ~1,000 hours against ~15,000–25,000 for LEDs; check the packaging of the bulbs you buy).
- Lumens, not wattage, measure light — compare lumens when you shop.
Walking through the calculation, step by step
The calculator on this page does one thing, and it does it in the open: it turns the numbers you type into the answer shown in the result table, using the formula above it. There is no hidden adjustment and no extra factor added after the formula. If you can follow the formula line by line, you can check the calculator by hand, and that is exactly what this section does. Start with the first field, number of bulbs, and read its help text before you type anything: the help tells you where the number comes from, and a number taken from the right place is the single biggest improvement you can make to the answer.
Here is the formula again, broken into its steps, in the order the calculator applies them:
- energy saved per year = bulbs × (old W − LED W) × hours per day × 365 ÷ 1,000 This line only changes the time scale of the answer: the same cost, expressed for a day, a month or a year.
- payback = bulb purchase cost ÷ money saved per year This line only changes the time scale of the answer: the same cost, expressed for a day, a month or a year.
Watch the units as you go, because most mistakes in this kind of calculation are unit mistakes, not arithmetic mistakes. The fields on this page use these units: W, bulbs, currency, hours, years. Power and energy are the pair that causes the most confusion: power, in watts or kilowatts, is a rate at which energy is used, and energy, in kilowatt-hours, is power multiplied by time. A 2,000 W heater running for one hour uses 2 kWh, and a 2 kW heater running for half an hour uses 1 kWh. Watts become kilowatts when you divide by 1,000, and kilowatt-hours are what your bill counts, so keeping those two apart is what makes the answer come out in the right size.
The worked example above is the best way to test whether you have understood the steps. It begins like this: Ten 60 W bulbs replaced by 8 W LEDs, on 5 hours a day at 0.1819 per kWh: each bulb saves 52 W, so the set saves 949 kWh and $172.62 a year. Read it slowly and match each number in it to a field above and to a line of the formula. Notice the order: the quantities are combined first, the rate is applied last, and the answer is then expressed for the period the example states. If you change one number in the example and keep the rest, the answer changes in the direction the formula predicts, and that is a useful habit: change one thing at a time, run the calculator again, and watch which output moves.
How to read your result
The result table on this page is a saving, not a cost, and it is worth reading it in that spirit. The headline figure is the money you would keep, over the period the calculator states, if the inputs you entered stay as they are. The other rows break that headline down: they show how the saving is built from the energy saved and the rate it is valued at, so you can see whether the saving comes mostly from using less energy or mostly from the price of the energy you no longer buy.
Read the result table row by row, in this order:
- Electricity saved per year is the row to read when you want that part of the answer on its own. Compare it with the headline row: if it is most of the total, it is the part to work on first, and if it is small, changing it will not move the answer much.
- Cost of the new bulbs is the row to read when you want that part of the answer on its own. Compare it with the headline row: if it is most of the total, it is the part to work on first, and if it is small, changing it will not move the answer much.
- Payback time is the row to read when you want that part of the answer on its own. Compare it with the headline row: if it is most of the total, it is the part to work on first, and if it is small, changing it will not move the answer much.
- Net saving over the projection (after bulb cost) is the row to read when you want that part of the answer on its own. Compare it with the headline row: if it is most of the total, it is the part to work on first, and if it is small, changing it will not move the answer much.
To judge whether your own answer is high or low, change only the rate and watch the result. The rates register on this site lists a United States national reference rate of 0.1819 per kWh, a Washington average of 0.1442, a Massachusetts average of 0.3019 and a Hawaii average of 0.4641. At those rates, 1,000 kWh costs $181.90, $144.20, $301.90 and $464.10. The same 1,000 kWh at the North Dakota average of 0.1246 costs $124.60, and the Montreal record in the register is 0.0829 per kWh, which gives 0.0829 times 1,000, or 82.90, for 1,000 kWh. The spread between those records is wider than most people expect, and it is why the rate matters as much as the amount you use: the same usage can cost roughly four times as much at the highest of those rates as at the lowest, and no change in how you use electricity can close a gap that comes from the price itself.
The worked example on this page puts the result in context. It ends with this conclusion: At 3 per bulb (30 total), the swap pays for itself in about 2.1 months and nets $1,696.23 over ten years. Hold your own result next to that conclusion and ask whether the two are in the same range for similar inputs. If yours is far away, the most likely cause is an input that does not match the example, and the field help text above will tell you which one to check first.
What affects the result most
Not every input matters equally, and the ranking is written into the formula. An input that the formula multiplies by moves the answer in proportion: double it, and the answer doubles, as long as everything else stays the same. An input that the formula divides by moves the answer the other way: raise it, and the answer falls. A fixed charge is different again: it does not move at all when you use more, so it matters most when use is low and least when use is high. Before you spend effort improving an input, check where it sits in this ranking, because a precise number for a small input is worth less than a rough number for the biggest one.
- Number of bulbs: raising this raises the result in proportion, because the formula multiplies by it. It is usually the input where a better measurement pays off first.
- Hours on per day (average): raising this raises the result in proportion, because the formula multiplies by it. It is usually the input where a better measurement pays off first.
- Old bulb wattage: raising this raises the result in proportion, because the formula multiplies by it. It is usually the input where a better measurement pays off first.
- LED wattage: raising this raises the result in proportion, because the formula multiplies by it. It is usually the input where a better measurement pays off first.
- Price per LED bulb: raising this raises the result in proportion, because the formula multiplies by it. It is usually the input where a better measurement pays off first.
- Project savings over: raising this raises the result in proportion, because the formula multiplies by it. It is usually the input where a better measurement pays off first.
- Standing charge: this adds the same amount every day, so it does not change when you use more energy. When use is low it can be a large share of the total, and when use is high it fades into the background.
A useful check is the doubling test. Take the worked example on this page, double its main quantity in your head, and ask what the formula would give: for a quantity the formula multiplies by, the answer doubles too. That is why the first thing to get right is the quantity itself — the amount used, the hours run, the area, or the distance — and the second thing is the rate or price. Everything else on the page is either a conversion between units, which the formula handles for you, or a fixed amount, which you can read straight from a bill.
Common mistakes
Most wrong answers from this calculator come from the same few slips. They are easy to make and easy to check for, and checking for them takes less time than re-doing the whole calculation:
- Mixing up watts and kilowatt-hours. Watts describe how fast an appliance uses energy; kilowatt-hours describe how much energy it has used. Entering a wattage where the calculator asks for energy, or the reverse, makes the answer wrong by a factor of a thousand or by the number of hours, and the mistake is easy to miss because the result still looks like a plausible number.
- Using the wrong rate. A preset average is a starting point, not your tariff. If your bill shows a different rate, use that one: the calculator multiplies by the rate you enter, so a rate that is a few cents out moves the whole answer by the same proportion.
- Mixing up the period. A monthly figure entered where the calculator asks for a year, or a daily figure where it asks for a month, throws the answer out by a factor of twelve or thirty. Check the unit next to every field before you type, and check the period the result is stated for before you compare it with a bill.
- Rounding too early. Rounding each step of a calculation before the next step uses the rounded number, and the rounding adds up. Enter the full numbers the calculator asks for, let it do the arithmetic, and round only the final answer when you quote it.
- Ignoring what the calculator leaves out. The assumptions section above lists what is not included in the answer — fixed charges, taxes, maintenance, installation and other costs, depending on the calculator. Treating the result as a complete bill, or as a complete saving, is the most common way to be disappointed by it afterwards.
Getting the most from the saving
The result on this page is a starting point, not a verdict. These are the practical ways to use it:
- Start with the hours. The saving in this calculator grows with the hours the item is used, so the biggest saving comes from the item that runs longest, not the one with the biggest wattage on its label. Rank your items by hours first, then by power.
- Use your own rate. The saving is valued at the rate you enter, so a saving calculated at a preset average is only as good as that average. Put your own rate in and the saving becomes a number about your home, not about an average home.
- Count the full cost of the change. A saving that takes years to pay for the item that produces it is a different decision from a saving that pays for itself quickly. The payback figure on this page is the way to compare the two, and it uses the same inputs as the saving itself.
- Re-run the calculation with measured numbers. After a year, the numbers you guessed at the start can be replaced with numbers you measured: the hours you actually used, the rate you actually paid. The second calculation is the one to trust.
Frequently asked questions
Why does the calculator ask for number of bulbs?
Because the formula needs it, and because it is the number most people get wrong. The help text next to the field says where the number comes from, and using the number from that source — a bill, a meter reading, a label, or a measured figure — is what makes the answer about your home rather than about an average one.
Can I use the preset rate, or should I use my own?
Use your own rate whenever you have it. The presets on this page are published averages or regulated figures, provided as starting points so the calculator works before you have a bill to hand. Your own rate, taken from a recent bill, is always the more accurate input, and the result moves in proportion to it.
Does the result include tax?
The calculator applies the rate you enter exactly as you enter it. If the rate you type already includes tax, the result includes it; if it does not, the result does not, and tax must be added afterwards. Where a calculator on this site has its own tax field, that field is the place to enter it, and the assumptions section above says which case applies to this page.
Will I really save this much?
The saving on this page is modelled, not measured: it follows from the inputs you entered and the assumptions listed above. If the hours, the rate or the efficiency turn out differently in your home, the saving will be different too. Treat it as a plan to check against a year of real use, and re-run the calculator with measured numbers when you have them.